Step-by-Step DIY Fix Guide
- SAFETY: Disconnect power at the circuit breaker.
- Visually inspect the bake element at the bottom of the upper oven cavity — look for a visible break, blister, or burn mark. A failed element typically shows physical damage.
- If the bake element is visibly damaged, it can be replaced: unscrew the two mounting brackets inside the oven, pull it forward, disconnect the wires, and connect the new element.
- If the bake element looks intact, test the oven temperature sensor (see F1 steps) — a faulty sensor can mask heating issues.
- If both the element and sensor appear good, the control board relay has likely failed — call a technician.
If the warning comes back after restart
- If the warning returns immediately after a clean restart, the sensor or wiring path becomes more likely than a one-time glitch.
- F6 persists after replacing the bake element and confirming the temperature sensor is good
What This Error Means
Error F6 on your LG oven means: The upper oven is not reaching the set temperature within the expected time. The bake or broil heating element or its control circuit has failed. The range's self-diagnostic system has detected this condition.
The most frequent cause is bake element burned out — visible as a break or blister on the element wire at the bottom of the oven cavity. Work through the causes and fix steps below in order — many LG oven errors are resolved without a service call.
Many cases of F6 can be resolved by the homeowner. The steps below cover the full DIY checks — if they do not resolve the error, a technician is needed.
Oven temperature sensor faults are among the most common LG oven errors. The sensor is a simple probe on the back wall of the oven cavity — reconnecting a loose harness connector resolves around half of all sensor fault codes. Sensor replacement is a 15-minute DIY repair when the connector check does not resolve it.
Most Likely Cause by Symptom
The LG oven may stop, pause, or refuse to complete the cycle normally.
Likely cause: Bake element burned out — visible as a break or blister on the element wire at the bottom of the oven cavity
Check first: SAFETY: Disconnect power at the circuit breaker.
The warning may return immediately because the appliance is detecting an internal fault.
Likely cause: Broil element failure — less common but can cause F6 if broil circuit is part of the preheat
Check first: Visually inspect the bake element at the bottom of the upper oven cavity — look for a visible break, blister, or burn mark. A failed element typically shows physical damage.
Common Causes
- Bake element burned out — visible as a break or blister on the element wire at the bottom of the oven cavity
- Broil element failure — less common but can cause F6 if broil circuit is part of the preheat
- Oven temperature sensor giving a false high reading — making the board think the oven is hotter than it is
- Bake element relay failure on the control board
What Not to Do
- Do not reach into the oven to test the bake element with the power on — the element terminals are live
Model and Display Variation Notes
Model-family notes
- LG oven display wording and code formats can vary by series.
- If your model behaves differently, check the owner manual before trying any deeper maintenance step.
Display and panel differences
- Panel wording can vary by series, so confirm the exact code pattern before buying parts.
Parts, Tools and Service Options
Service option
LG service visit if the warning returns after the basic checks are complete.
Manual and model check
Check your exact model and manual before ordering any LG oven parts.
Common parts
- Bake element if element is burned out ($20–$60)
- Broil element if broil element has failed ($25–$70)
- Main control board if relay has failed ($100–$250)
This section stays service-first because the page points more strongly toward support or professional repair than a routine parts purchase.
When Not to Keep Troubleshooting
F6 persists after replacing the bake element and confirming the temperature sensor is good
How to Prevent It Recurring
- Avoid placing aluminum foil on the oven floor — it reflects heat onto the bake element and causes overheating and premature failure
Related Error Codes
F1
The upper oven temperature sensor (thermistor) is reading an open circuit — its resistance is outside the valid range, meaning the oven cannot monitor temperature in the upper cavity.
F9
The upper oven is not heating at all — the control board is not detecting any temperature rise from the bake element during a bake cycle. The oven is completely cold during operation.
F19
LG oven error F19 usually means the oven can heat up, but it is not maintaining the set temperature reliably.
Extra notes
- This page is based on LG support material and stays conservative where model-specific guidance may vary.
- The goal is to help you identify safe first checks before you move into parts, service, or model-specific manual lookup.
Source and model notes
Last reviewed: 2026-04-08
Based on: Based on LG support material and edited into consumer-safe guidance for the exact code family on this page.
Model coverage note: LG oven code meanings can vary by series, control panel, and model family, so use this page as a safe starting point rather than a replacement for the model-specific manual.
Important: FixThisError is an independent guide, not the manufacturer. Use your model-specific manual when the panel wording or behavior differs.
Always disconnect power before inspecting appliances. If unsure, contact a licensed appliance technician.