Step-by-Step DIY Fix Guide
- SAFETY: Switch the range off and disconnect power at the circuit breaker.
- Reset by restoring power after 30 seconds.
- If E011 returns, call Bosch Customer Support at 1-800-944-2904.
If the warning comes back after restart
- If airflow still seems weak after the basic checks, the fan path or a deeper obstruction becomes more likely.
- If the warning returns immediately after a clean restart, the sensor or wiring path becomes more likely than a one-time glitch.
- Any recurrence after power reset — E011 requires professional diagnosis and repair
What This Error Means
Error E011 on your Bosch range means: The oven's temperature sensor (NTC probe) has an open-circuit fault or has failed, preventing the range from accurately measuring oven cavity temperature. The appliance's self-diagnostic system has flagged this condition and may have disabled the affected zone or function to prevent damage or unsafe operation.
The most frequent cause is failed or open-circuit ntc temperature sensor inside the oven cavity. Work through the causes and fix steps below in order — starting with the simplest check.
Bosch's official guidance classifies E011 as a technician-only fault. The components involved require specialist testing equipment and safe internal access. Contact Bosch Customer Support at 1-800-944-2904.
A faulty temperature sensor means the appliance cannot accurately measure heat — it may overheat (if the sensor reads low) or refuse to heat at all (if the sensor reads high or open). Running the appliance with a failed sensor risks damaging heating elements, food, or the appliance itself.
Most Likely Cause by Symptom
The Bosch range may stop, pause, or refuse to complete the cycle normally.
Likely cause: Failed or open-circuit NTC temperature sensor inside the oven cavity
Check first: SAFETY: Switch the range off and disconnect power at the circuit breaker.
The warning may return immediately because the appliance is detecting an internal fault.
Likely cause: Wiring fault or broken wire between sensor and control board
Check first: Reset by restoring power after 30 seconds.
Common Causes
- Failed or open-circuit NTC temperature sensor inside the oven cavity
- Wiring fault or broken wire between sensor and control board
- Control board sensor input circuit failure
- Sensor physically damaged by a utensil or during oven cleaning
What Not to Do
- Do not cook with E011 active — the range cannot maintain accurate temperature
- Do not attempt to bypass or remove the sensor yourself
Model and Display Variation Notes
Model-family notes
- Bosch range display wording and code formats can vary by series.
- If your model behaves differently, check the owner manual before trying any deeper maintenance step.
Display and panel differences
- Panel wording can vary by series, so confirm the exact code pattern before buying parts.
Parts, Tools and Service Options
Service option
Bosch service visit if the warning returns after the basic checks are complete.
Manual and model check
Check your exact model and manual before ordering any Bosch range parts.
Common parts
- Oven NTC temperature sensor ($20–$50)
- Wiring harness section if wiring is damaged ($25–$60)
- Oven control board if sensor circuit has failed on the board ($100–$250)
This section stays service-first because the page points more strongly toward support or professional repair than a routine parts purchase.
When Not to Keep Troubleshooting
Any recurrence after power reset — E011 requires professional diagnosis and repair
How to Prevent It Recurring
- Avoid contact with the small temperature probe (metal rod protruding into the oven cavity) when loading or unloading pans
- Use oven-safe thermometers rather than probing the sensor itself to verify temperature
Related Error Codes
E11
The oven's NTC (negative temperature coefficient) temperature sensor has failed or has an open-circuit fault, preventing the oven from measuring cavity temperature.
E100
The oven cavity temperature exceeded the safe maximum limit and the safety shutoff has stopped the heating elements to prevent damage or fire.
E126
The oven's main control board has detected a communication failure between internal electronic modules, preventing normal operation.
Extra notes
- This page is based on Bosch support material and stays conservative where model-specific guidance may vary.
- The goal is to help you identify safe first checks before you move into parts, service, or model-specific manual lookup.
Source and model notes
Last reviewed: 2026-04-07
Based on: Based on Bosch support material and edited into consumer-safe guidance for the exact code family on this page.
Model coverage note: Bosch range code meanings can vary by series, control panel, and model family, so use this page as a safe starting point rather than a replacement for the model-specific manual.
Important: FixThisError is an independent guide, not the manufacturer. Use your model-specific manual when the panel wording or behavior differs.
Always disconnect power before inspecting appliances. If unsure, contact a licensed appliance technician.