fixthiserror_

BOSCH E06

Bosch Dishwasher Error Code E06: Door Sensor Circuit Fault

Clear meaning, realistic next steps, and safe guidance without turning the page into a long repair manual.

What it means

There is a door sensor circuit fault/error.

Severity

Medium - some user checks may help, but repeated faults often need service.

Can you fix it yourself?

Partial — start with DIY steps

Most likely cause

Damaged or misaligned door latch sensor

Estimated time for safe first checks: 10–20 min.

Step-by-Step DIY Fix Guide

  1. SAFETY: Disconnect power at the breaker.
  2. Inspect the door latch for visible damage, misalignment, or debris.
  3. Clean around the latch mechanism with a damp cloth.
  4. Close the door firmly and restore power to test.
  5. If E06 returns, the door latch switch or wiring needs replacement.

If the warning comes back after restart

  • If the door closes normally but the warning keeps returning, the latch or switch path becomes more likely than a simple alignment issue.
  • If airflow still seems weak after the basic checks, the fan path or a deeper obstruction becomes more likely.
  • If the warning returns immediately after a clean restart, the sensor or wiring path becomes more likely than a one-time glitch.

What This Error Means

Error code E06 on your Bosch dishwasher indicates: There is a door sensor circuit fault/error. The appliance detects this condition through its built-in sensors and halts the current cycle to prevent further damage. Depending on the model, the code may flash on the display panel, appear on a digital readout, or cause the status lights to blink in a specific sequence. The dishwasher will not resume normal operation until the underlying fault is resolved.

The most frequent cause of error E06 is damaged or misaligned door latch sensor. When this happens, the dishwasher's control board detects the abnormal sensor reading or motor response and triggers the fault code as a protective measure. Other contributing factors are listed in the causes section below — working through them in order is the fastest path to a fix.

Many cases of error E06 can be resolved with DIY troubleshooting — start with the steps below before calling a technician. If the steps do not clear the code, the fault is deeper in the system and professional diagnosis will be needed. The guide specifies clearly at which point to stop DIY work.

The dishwasher will display E06 and refuse to start or continue a cycle until the fault is resolved. If the code appeared mid-cycle, there may be water standing in the tub — which is normal for this fault type. Do not attempt to restart the appliance without working through the troubleshooting steps below first.

Most Likely Cause by Symptom

The Bosch dishwasher may stop, pause, or refuse to complete the cycle normally.

Likely cause: Damaged or misaligned door latch sensor

Check first: SAFETY: Disconnect power at the breaker.

The appliance may fail to start because the door or lock state cannot be confirmed.

Likely cause: Wiring fault between door latch and control board

Check first: Inspect the door latch for visible damage, misalignment, or debris.

The warning may return immediately because the appliance is detecting an internal fault.

Likely cause: Worn door latch assembly causing intermittent signal

Check first: Clean around the latch mechanism with a damp cloth.

Common Causes

  • Damaged or misaligned door latch sensor
  • Wiring fault between door latch and control board
  • Worn door latch assembly causing intermittent signal
  • Debris blocking the door switch mechanism

What Not to Do

  • Do not run further cycles until the fault is resolved

Model and Display Variation Notes

Model-family notes

  • Bosch dishwasher display wording and code formats can vary by series.
  • If your model behaves differently, check the owner manual before trying any deeper maintenance step.

Display and panel differences

  • Panel wording can vary by series, so confirm the exact code pattern before buying parts.

Parts, Tools and Service Options

Common parts

  • Door latch assembly ($25–$65)
  • Door switch ($15–$40)

Manual and model check

Check your exact model and manual before ordering any Bosch dishwasher parts.

Service option

Bosch service visit if the warning returns after the basic checks are complete.

Suggestions in this section are organized to support the troubleshooting flow first. Any future affiliate relationships should be disclosed clearly.

When Not to Keep Troubleshooting

Door latch is visibly broken or cracked

  • Error persists after cleaning and firmly closing door

How to Prevent It Recurring

  • Avoid slamming the dishwasher door — it stresses the latch sensor over time

Related Error Codes

Extra notes

  • This page is based on Bosch support material and stays conservative where model-specific guidance may vary.
  • The goal is to help you identify safe first checks before you move into parts, service, or model-specific manual lookup.

Source and model notes

Last reviewed: 2026-04-07

Based on: Based on Bosch support material and edited into consumer-safe guidance for the exact code family on this page.

View Bosch US Official

Model coverage note: Bosch dishwasher code meanings can vary by series, control panel, and model family, so use this page as a safe starting point rather than a replacement for the model-specific manual.

Important: FixThisError is an independent guide, not the manufacturer. Use your model-specific manual when the panel wording or behavior differs.

Always disconnect power before inspecting appliances. If unsure, contact a licensed appliance technician.